Offered in show-quality chrome or black. Easy 10-minute installation, like plug and play. Find and unplug the O2 sensor wires from the wiring harness.
Feed the end of the wires. Through the frame so they are free from the motorcycle. NOTE: Pay attention to wire routing. Loosen the heat shield clamps on both the front and rear exhaust pipes.Access to the head pipe mounting nuts. Remove the two head pipe mounting nuts from each flange, located at the cylinder head. Remove the clamp bolt which mounts the rear head pipe to the belt drive cover bracket. Remove the two bolts from each muffler body where they attach to the mounting bar. Remove exhaust pipes from the motorcycle and set aside. Remove the belt drive cover and take the bracket off the rear cover bolt, the bracket will not be reused. Remove the e-clip from the brack rod lynchpin. Remove the right side rider foot controls. Carefully remove the O2 sensors from the stock head pipes and save them for reuse with the new. Remove the three mounting bolts and washers attaching the exhaust mounting bar, save. Carefully remove exhaust port flanges and circlips from the stock exhaust system using snapring pliers. NOTE: Replace bent or damaged circlips.
Replace the exhaust gaskets with the supplied gaskets. Loosen all heat shield clamps. Install the exhaust end caps using 1/4 bolt to 30-33 Ft/Lbs (supplied).
Tighten all heat shield clamps. Install exhaust port flanges and circlips on new headers. Install and tighten supplied mounting bracket using stock washers and bolts. NOTE: To ease exhaust installation, insert one of the 5/8 flange head bolts into the upper.
Right hole of the bracket before installation. Torque the 3/8 bolt to 30-33 Ft/Lbs. And the two 1/4 bolts to 80-120 In/Lbs. Re-install brake rod into rear junction, replacing pin and e-clip. Apply a small amount of anti-seize compound to the threads of the O2 sensors and install them into the new head pipes.Models using 12mm oxygen sensors install 18mm to 12mm oxygen sensor adapter(supplied). Models not using oxygen sensors install 18mm plug. NOTE: Be careful not to get anti- seize on sensor tip, it may affect sensor function.
Using stock flange nuts, carefully install head pipes into exhaust ports (Assistance may be required). NOTE: Do not tighten the nuts at this time. Slide nut plates inside brackets welded to backside of muffler bodies. While holding nut plates in place, attach muffler bodies to mounting bracket using four 5/16x 5/8 flange head bolts (supplied).Leave them loose at this time. Tighten cylinder port exhaust flange nuts on front and rear cylinders while making sure pipes are parallel. Tighten the bracket flange head bolts on both mufflers. Plug O2 sensors back into wiring harness and route wires away from hot areas of motorcycle.
Check for adequate clearance of all exhaust system components and motorcycle accessories prone to heat damage. Be sure to tighten all hardware before starting motorcycle. These instructions are written for late model motorcycles equipped with O2 sensors.
Installing these pipes on a bike which is not equipped with O2 sensors, ignore all instructions. When installing a new set of exhaust pipes, make sure your hands are clean and free of oil. Installation, thoroughly clean pipes with a soft cloth and soapy water that will leave no residue before starting the motorcycle. Dry with a soft towel. Any residue will stain the finish when it heats up.
Do not use solvents or abrasive cleaners which can damage the finish. Avoid long periods of idling as this can cause discoloration. Intake leaks can cause the engine to run lean and overheat, this could lead to discoloration.Make sure there are no exhaust leaks at the junction of the exhaust pipes and cylinder head. In California, in order to meet Air Resources Board emissions requirements, certain aftermarket part applications have been identified as replacements, and others have received ARB Executive Orders. All other emissions related aftermarket parts are for competition use only. Thank you for shopping with us. In an effort to best control our inventory levels, we reserve the right to limit quantities or cancel unpaid orders. Please note: Inventory is not reserved until the item is paid for. We process our orders the same day we receive them! Sorry for all the inconvenience. For example, if you live in an apartment without a doorman. If this is a concern, be sure to provide an address where someone will be around to sign. The cost is too high. G wrong item or size or the merchandise received is not as described, you will not be responsible for the return cost. The item "SLIP ON PIPE MUFFLER EXHAUST FIT for Harley 2014 2019 XL883C X48 V72 IRON 883 M2" is in sale since Friday, August 2, 2019. This item is in the category "eBay Motors\Parts & Accessories\Motorcycle Parts\Exhausts & Exhaust Systems\Silencers, Mufflers & Baffles". The seller is "comtecllc2010" and is located in Sacramento, California.
This item can be shipped to United States, Canada, United Kingdom, Denmark, Romania, Slovakia, Bulgaria, Czech republic, Finland, Hungary, Latvia, Lithuania, Malta, Estonia, Australia, Greece, Portugal, Cyprus, Slovenia, Japan, China, Sweden, South Korea, Indonesia, Taiwan, South africa, Thailand, Belgium, France, Hong Kong, Ireland, Netherlands, Poland, Spain, Italy, Germany, Austria, Bahamas, Mexico, New Zealand, Philippines, Singapore, Switzerland, Norway, Saudi arabia, United arab emirates, Qatar, Kuwait, Croatia, Malaysia, Colombia, Antigua and barbuda, Aruba, Belize, Dominica, Grenada, Saint kitts and nevis, Saint lucia, Turks and caicos islands, Barbados, Bangladesh, Bermuda, Brunei darussalam, Bolivia, Egypt, French guiana, Guernsey, Gibraltar, Guadeloupe, Iceland, Jersey, Jordan, Cambodia, Cayman islands, Liechtenstein, Sri lanka, Luxembourg, Monaco, Macao, Martinique, Maldives, Nicaragua, Oman, Pakistan, Paraguay, Reunion, Uruguay, Montserrat.